Name: EQiblyReoke
Company: google
Email: taanakeif@gazeta.pl
Phone: 85929743346
Message: <h2> with the Balanset-1A Device </h2> <h3> Getting the Equipment Ready </h3> <ul> <li> accelerometers, laser rpm sensor, mounting stand, software application, and additional tools. </li> <li> Connect the device to your PC using the USB interface and confirm the software installation. </li> </ul> <h3> Setting Up the Sensors </h3> <ul> <li> Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings. </li> <li> Direct the laser speed sensor towards the rotor and affix reflective tape to the rotor surface to facilitate phase angle measurement. </li> </ul> <h3> Starting the Program </h3> <ul> <li> Initiate the Balanset program on your computer. </li> <li> Choose the correct balancing method (single or two-plane) according to the rotor configuration and the balancing task. </li> </ul> <h3> Initial Vibration Measurement </h3> <a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank"> <img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;"> </a> <ul> <li> Run the rotor up to its operating speed. </li> <li> The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition. </li> </ul> <h3> Trial Weight Installation </h3> <a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank"> <img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;"> </a> <ul> <li> Bring the rotor to a standstill and affix a trial weight at a predetermined point on the rotor, specifying its mass in the software (typically in grams). </li> <li> Run the rotor again, allowing the software to measure the effects of the trial weight on vibration and phase. </li> </ul> <a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank"> <img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;"> </a> <h3> Calculating the Correction Weight </h3> <ul> <li> Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle. </li> <li> The results of the calculation are shown both numerically and visually through charts and graphs. </li> </ul> <a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank"> <img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;"> </a> <h3> Installing the Correction Weight </h3> <ul> <li> Install the correction weight on the rotor according to the software's calculations. </li> <li> Periodic checks can be performed to ensure the balancing procedure is effectively reducing the vibration. </li> </ul> <a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank"> <img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;"> </a> <h3> Validation and Conclusion of the Balancing Process </h3> <ul> <li> With the compensating weight attached, operate the rotor and assess the level of any residual vibration. </li> <li> If the measured vibration falls within the tolerance defined by ISO 1940, the balancing process is considered successful. </li> <li> Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed. </li> </ul> <h3> Generating a Documentation of the Balancing Results </h3> <ul> <li> All balancing results are logged and archived within the software, from which you can produce a printable report summarizing the vibration levels, compensating weight, and its installation position. </li> </ul> <h3> Concluding Steps and Verification </h3> <ul> <li> Double-check that all weights and sensors are securely fastened. </li> <li> Ensure the rotor rotates smoothly and without excessive noise. </li> <li> If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts. </li> </ul> <p> </p> Instagram: https://www.instagram.com/vibromera_ou/ Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL Our website about <a href="https://vibromera.eu "> ISO 14001 Environmental Management System </a> Machinio: https://www.machinio.com/listings/98380186-portable-balancer-vibration-analyzer-balanset-1a-full-kit-in-portugal Facebook: https://www.facebook.com/marketplace/item/350151228150722
Page: https://fivetwenty.io/